Automated Guided Vehicles (AGVs)
AGCO’s paint preparation area uses automated guided vehicles (AGVs), a type of robot that follows markers or wires in the floor, or uses vision or lasers. The AGVs are used to move racks of parts to and from the paint system. Small AGV load stations can handle loads less than 6 feet wide and less than 2,500 pounds. Large AGV load stations with specialized carts/dollies transport large assemblies like combine welded mainframes, large square baler mainframes or cabs to the track system, which moves the parts through the paint building. These large loads can be up to 56 feet long, 10 feet wide and 6,500 pounds.
AGCO_HESSTON_OPERATIONS_PAINT_FACILESS_AGV_1_300DPI_08162013.jpg.
AGCO_Hesston_Operations_Paint_Facility_AGV_2_300dpi_08162013.jpg
AGCO_Hesston_Operations_Paint_Facility_AGV_Loading_300dpi_08162013.jpg
E-Coat and Powder Paint Process
AGCO is the first agricultural equipment manufacturer to E-coat and powder-paint all major parts on harvesting and hay equipment products. About 75 percent of parts will ultimately go through the E-coat and powder paint process. The parts go through a 17-step process, beginning with the dip system, which removes rust, scale and laser oxides. Each of the 15 dip tanks is 35,000 gallons in capacity. E-coated parts are then baked in one of 10 cure ovens at 375–450º F before receiving powder paint. They are then baked in one of 10 powder-coat ovens at 425º F.
总工艺需要四个半小时，导致耐腐蚀性和风化的抗性增加，并具有较低的环境影响。通过液体涂料过程，约50％的涂料粘附，而其他50％是浪费。随着粉末涂料工艺，约95％的涂料转移到部分。粉末涂漆的颜色包括黑色，底盘灰色，Challenger®黄色，Gleaner®灰色，MasseyFer亚博在线手机端guson®的红色。
AGCO_Hesston_Operations_E_Coat_1_300dpi_08162013.jpg
一个拾穗的人。焊接主机拿起的special hanging device. It is placed into the first high-temperature dip tank, containing a 160º F alkaline solution, for 90 seconds. Each of these 15 dip tanks is 35,000 gallons in capacity.
AGCO_Hesston_Operations_E_Coat_2_300dpi_08162013.jpg
b. In the second and third dip tanks, the parts to be painted are rinsed at ambient temperature for 30 seconds each.
AGCO_Hesston_Operations_E_Coat_3_300dpi_08162013.jpg
AGCO_Hesston_Operations_E_Coat_4_300dpi_08162013.jpg
c. Acid-solution dip tanks, both at 160º F, are used to remove any rust, scale and laser oxides.
AGCO_Hesston_Operations_E_Coat_5_300dpi_08162013.jpg
d. Rinsing through four additional tanks occurs: a rinse tank at ambient temperature; an alkaline solution at 160º F for one minute; and finally, two reverse-osmosis rinse tanks at ambient temperature.
AGCO_Hesston_Operations_E_Coat_6_300dpi_08162013.jpg
AGCO_Hesston_Operations_E_Coat_7_300dpi_08162013.jpg
e. The combine mainframe is ready for a zirconium coat dip tank, then two more reverse-osmosis rinse tanks at ambient temperature.
AGCO_Hesston_Operations_E_Coat_8_300dpi_08162013.jpg
f. A combine mainframe reaches the E-coat tank where it receives E-coat primer with a high-voltage and high-amperage charge for 180 seconds. It is then processed through two more rinse tanks, both at ambient temperature.
AGCO_Hesston_Operations_E_Coat_9_300dpi_08162013.jpg AGCO_Hesston_Operations_E_Coat_10_300dpi_08162013.jpg AGCO_Hesston_Operations_E_Coat_11_300dpi_08162013.jpg
g. The frame will now go to one of the 10 E-coat ovens to be baked at 375º F for 40 minutes. This is followed by a 20- to 60-minute cooldown.
AGCO_Hesston_Operations_E_Coat_12_300dpi_08162013.jpg
h. Parts going to the three powder booths will be painted one of five different colors. These booths feature an automatic section of 32 paint guns and two manual reinforcement painters.
AGCO_Hesston_Operations_Powder_Paint_1_300dpi_08162013.jpg AGCO_Hesston_Operations_Powder_Paint_2_300dpi_08162013.jpg
i. AGCO’s powder paint system features reclaim booths that fully reclaim all unused powder. After being powder-painted, parts go to the powder oven for 60 minutes.
AGCO_Hesston_Operations_Powder_Paint_3_300dpi_08162013.jpg
j. The finished Gleaner welded mainframe has a high-quality surface that will resist rust and hold its appearance for years.
AGCO_Hesston_Operations_Painted_Chassis_300dpi_08162013.jpg
Liquid Paint System
The liquid line is set up to paint six different colors: black, chassis gray, Challenger yellow, Gleaner gray, Massey Ferguson red and Fendt® green. All parts painted in the liquid paint system undergo a six-step process similar to the powder-paint system. The parts washer system has a 5,200-gallon capacity and 500 spray nozzles. The main spray pump flows at 1,735 gpm. Inside the 40-foot paint booths, the down-draft system flows a minimum of 100 feet per minute (fpm), with 80,000 cubic feet per minute (cfm) exhaust flow per booth. After priming and painting, racks of parts move into one of four ovens and are baked at 200º F for 45 minutes.
AGCO_Hesston_Operations_Liquid_Paint_System_1_300dpi_08162013.jpg
AGCO_Hesston_Operations_Liquid_Paint_System_2_300dpi_08162013.jpg
4205 River Green Parkway, Duluth, GA 30096-2563 USA
Telephone: 770-813-9200www.AGCOnews.com/na